How to Resurface Concrete? 10 Tips To Follow

Concrete is a popular material for driveways, patios, and sidewalks. However, over time it can become stained and appear worn. To restore the appearance of your concrete, there are several steps that you can take. These tips will help you resurface your concrete!

Resurfacing Concrete
Resurfacing Concrete

1. Cover With Plastic

If you have a driveway or sidewalk that needs resurfacing, the first step is to cover it with plastic. If there are no cracks in the concrete and just a few minor scratches, then you can use sandpaper instead of a sander. You can save on sandpaper through coupons.

2. Read The Instructions

Be sure to carefully read any instructions before beginning work. Some surfaces may require different steps than others do. It’s important not to pour hot asphalt into colder temps as this could cause problems with the product settling correctly once dry. 

3. Check About Cold Nights

If your area gets cold at night, be careful about working after sunset if possible. Without proper heat, curing might still happen during cooler temperatures overnight. It will result in cracking issues when exposed to extra stresses like car traffic the next day.

4. Use Brush

You can use a broom or brush to apply the asphalt. The type of surface you are working on will determine which one works best. A flat driveway may require a bristle brush, while an angled driveway would need something with stiffer bristles that won’t bend in between slats etc. You can check for coupons on brushes for savings.

5. Remove Excess Particles

Tack cloths are used to remove excess loose particles from concrete before applying sealant and hot top coatings after work are complete. This step isn’t always necessary, depending on what products you use. Check for offers on tack clothes for savings.

6. Get Rid Of Cracks

To get rid of any cracks in the concrete, you can use a hammer drill or grinder with diamond bits. It depends on how deep they are and how much material needs to you need to remove for them to disappear. For example, if it’s just an inch-long crack that’s not too wide, then using either of these tools by hand will work fine. 

A giant hole might need something more heavy-duty, like an angle grinder fitted with a masonry blade. Check for discounts on hammer drills for savings.

7. Wear Safety Equipment

Concrete resurfacing is messy, so wear gloves, goggles/safety glasses, and protective clothing. Be sure to also have breathing masks on hand for when mixing certain products. Inhaling some of this stuff can cause respiratory problems/allergies etc.

8. Estimate Asphalt Amount

Depending on the depth of your project, you may need to use more than one bag of asphalt or resurface product. So keep that in mind when shopping for supplies and how much money it will cost overall. If using sandpaper instead, make sure not to get anything too coarse as results could lead to scratching rather than smoothing out concrete efficiently depending on what tools are being used. Don’t forget about other variables like humidity, either!

Use right amount
Use right amount

9. Rent The Tools

If your project is small enough, you can rent a power grinder for the job. Make sure that they have diamond blades available before renting, though. Some hardware stores also carry similar tools but only in bigger sizes. So if you need one of these things, then go with renting something versus buying because even if purchased would probably be more than what you needed

10. Dry Properly

Apply two coats of sealer using a sponge mop or clean cloth, allowing each coat to dry thoroughly before applying the next one. Be sure you are adequately ventilated for this part! The product should be involved in thin layers and not allowed to pool up on top of itself. 

So, it can cure appropriately without forming unsightly cracks or peeling off prematurely. Let dry overnight between each layer if possible. If you have access to fans, that will help speed things along.

Summing Up

Many homeowners are looking for ways to make their concrete surfaces look better. Concrete is a durable construction material, but it can crack, chip, and lose its color over time. Resurfacing is the best solution. Be sure to follow our ways to do it perfectly. You can also check for tips to drill in concrete for further help.